How to build an 'Ion Source Beam Projector' by James Fauble

Below are simple instructions describing how to assemble an "Ion Beam Projection Device" which can be used for many various applications including the collection of "Ionized Particles" IE - free electrons and protons/positrons from radiant energy sources. The type of device that I will describe also has numerous other applications of which I will not attempt to describe in detail although, any of you with a high school education and/or a basic knowledge of physics or electronics should be able to figure many of them out with a small amount of brain work.

This is a low energy model of similar technologies that are currently being used in many existing applications such as MRI, Cyclotron, Kryotron, Particle Accelerators etc..... . Also, here are a couple of links to similar devices which should give you an idea of the methodology and functions of this sort of technology. (http://thunder.prohosting.com/~hamel/index.htm), (http://content.aip.org/RSINAK/v74/i2/956_1.html).

You can also search "Google" for "magnetic beam projection", "Ion beam projection", etc.. .

I have personally built the device which I will describe below and can testify that it worked very well for projecting a concentrated ion beam although it was not what I was trying for at the time. Contrary to common beliefs, this is not complicated science and just about anyone can do this. Well then, why are MRIs so expensive? My guess is, God only knows! LOL. Who knows, maybe after enough people find out how simple and inexpensive it can be done, our medical bills will have to go down eh? OUCH, the medical community won't like that will they! Oh no, we can't have that now can we?

Extreme Caution: I would also like to advise anyone building this device not to point or aim it towards your head or anyone else's head as it is known that high energy static magnetic fields such as are produced by this devise have been used by some areas of the medical community for anti-depression therapy and also, that if used improperly can actually cause clinical depression. This is NOT a toy, this technology has the potential of being used for good or for bad purposes. For example: The medical community uses this technology for good, on the other hand, the government/military establishment uses it for very bad things. I will assume NO responsibility for any problems or damages resulting from the assembly or use of this device. I only wish to make this knowledge available to more people so that others will become aware of what is out there already and possibly being used on them. Do you ever hear voices in your head? Has anything ever happened to someone you know that could not be explained by anyone other than a psychiatrist? Well, this kind of technology shines a whole new light on some of these things. Consider this? All biological systems operate at varying frequencies which control certain functions within the body.

A subject’s bioelectric field can be remotely detected, so subjects can be monitored anywhere they are. With special EMF equipment NSA cryptologists can remotely read evoked potentials (from EEGs). These can be decoded into a person’s brain-states and thoughts. The subject is then perfectly monitored from a distance. NSA personnel can dial up any individual in the country on the Signals Intelligence EMF scanning network and the NSA’s computers will then pinpoint and track that person 24 hours a day. The NSA can pick out and track anyone in the US.

The NSA records and decodes individual brain maps (of hundreds of thousands of persons) for national security purposes. EMF Brain Stimulation is also secretly used by the military for brain-to-computer link (in military fighter aircraft, for example). For electronic surveillance purposes, electrical activity in the speech center of the brain can be translated into the subject’s verbal thoughts. RNM can send encoded signals to the brain’s auditory cortex, thus allowing audio communications direct to the brain (bypassing the ears). NSA operatives can use this covertly to debilitate subjects by simulating auditory hallucinations characteristic of paranoid schizophrenia. Without any contact with the subject, Remote Neural Monitoring can map out electrical activity from the visual cortex of a subject’s brain and show images from the subject’s brain on a video monitor. NSA operatives see what the surveillance subject’s eyes are seeing. Visual memory can also be seen. RNM can send images direct to the visual cortex, bypassing the eyes and optic nerves. NSA operatives can use this surreptitiously to put images into a surveillance subject’s brain while they are in REM sleep for brain-programming purposes.

There has been a Signals Intelligence network in the US since the 1940s. The NSA, Ft Meade has in place a vast, two way, wireless RNM system which is used to track subjects and non-invasively monitor audiovisual information in their brains. This is all done with no physical contact with the subject. RNM is the ultimate method of surveillance and domestic intelligence. Speech, 3D sound, and subliminal audio can be sent to the auditory cortex of the subject’s brain (bypassing the ears), and images can be sent into the visual cortex. RNM can alter a subject’s perceptions, moods, and motor control. Speech cortex/auditory cortex link has become the ultimate communications system for the intelligence community. RNM allows for a complete audiovisual brain-to-brain link or brain-to-computer link.

Now What If? A device were available that could project any kind of information in a straight path and which could concentrate any given frequency towards a specific location, person, or even a specific part of that person? Do you get it yet? I know personally, people that have been subjected to this kind of harassment and torture and no one else ever knew what had happened. That is all I can say or want to say on the subject. This is what we have to deal with in our current world these days folks and so I suggest you think about this just in case. Just one more application of this kind of technology and I do not recommend the use of this device for such purposes. Also, this is another reason that I will only describe some basic low energy designs on this forum. Now with that out of the way!

1. You will need to find two quadrupole doughnut or ring shaped Ferrite ceramic magnets measuring approximately 4 3/4" to 5" total diameter with a center hole measuring approximately 1 3/4" to 2" diameter. The thickness of the magnets should be approx. 1/2" to 3/4". Also if possible, try to use a similar quality energy value Ferrite material as you have found for the other magnets in the assembly to ensure proper beam projection. Also, these are the most important element in the assembly or this device and these magnets must be quadropole magnets NOT the typical bi-pole or di-pole magnets. Many more expensive units use magnets with six or even eight separate poles in order to tune the ion beam to the desired width and energy level.

2. Next, You will need seven rectangular Ferrite ceramic magnets measuring approximately 1-7/8" L x 7/8" W x 3/8" Thickness. These same exact magnets can be found at any "Radio Shack" and are usually available from off the shelf, if not, you can order any desired number of them at the front counter. They are about 99 cents each so you probably won't break the bank. Also, it is a good idea to by extras in case some are broken during shipment or the during the assembly process.

3. Finally, although I have so far only used copper plated stainless steel sheet metal to cut my metal strips from, you will need some form of a flexible permeable metal strip measuring approximately 1-1/4" Wide by approx. 15-1/2" Long to fit around the seven rectangular magnets. Also, I am not yet sure that the copper plated stainless steel sheet metal is necessary in producing or projecting the ion beam. If you don't use copper plated stainless, and it still works, please let me know o.k.? As I have said, I did use copper plated stainless steel sheet metal and this worked perfectly. I do know that some of the relatively similar devices that I have seen have also used the copper plated stainless for focusing various beam projection devices. This seems to work similar to what an optical lens mechanism does in a light projector. Hopefully you can imagine what a strip of sheet metal would look like cut to this these measurement?

Who knows, maybe a person wouldn't need a huge towering antenna like Tesla described, to tap into the earth's ionosphere? I know, do you?

Please forgive me if this is confusing, I am no good at teaching or giving directions.

Alrighty then, put the seven magnets on their sides lengthwise and form them as uniformly as you can into a circle or at least as close as you can.

Now bend the metal strip around the arrangement and make sure it goes all the way around the entire set of magnets with an additional 1/2" being left over.

Next you will need to slice or cut a small triangle about 3/16" deep between each magnet into the edges of the metal strip which should be protruding past the width of the magnets themselves since the strip is supposed to be about a quarter inch or so wider than the width of the magnets. This is so you will be able to bend the edges of the metal strip over the sides of each magnet to keep them from slipping out of the assembly. Next, you should have all like poles of all seven magnets facing inward towards each other as pictured in (Reference #1) You may want to use a pop bottle or some sort of plastic container which can be used to keep the magnets from flying away from each other and breaking. Remember, opposites attract, like poles repel?

When you are done with this step, you will need to bend the ends of the metal strip so that they intersect or lock together. Pleas refer to (Reference #3). IE, bend or crimp one end inwards starting at about a quarter inch from the end of the strip then bend the opposite end outwards in the same fashion so that they can interlock. This metal strip should be fitted tightly against the outside faces of all seven rectangular shaped magnets and the metal strip or band should be made as snug as possible to hold the assembly together. This arrangement will not be a perfect circle but should instead have slight corners. If the strip is to long you can trim it if you like. The measurements I have given correspond to the device that I had built and I am quite sure that there is a lot of room for variation, however if you use the same materials as I have described and follow these directions properly this device will absolutely positively work. The secret is in the geometric relation of the magnets used and also the energy products associated in relation to each other.

This is also the secret to most if not all of the permanent magnetic motors that have broken the OU barrier. Anyhow, as I have said, this is a very simple assembly and design and there should not be a problem as long as similar or equivalent products are used together. On the other hand, if you already have a higher energy material on hand, you might want to try substituting the Ferrite materials with such materials although I cannot stress the necessity of using at least quadropole ring or doughnut shaped magnets of the same material and energy product as the side magnets are made of. Remember, (Regular di-pole magnets will not work in this type of design). Also if you have already assembled a "Halbach Array", (See Reference #s 4 & 5)

You may want to put this to use and simply buy the appropriate sized quadropole ring/doughnut magnets to fit the array. This should also increase the range and energy level of your device.

Lets Continue: The next step after making sure you have set all seven rectangular magnets in place with all same or like poles facing towards each other and then crimping the ends of the containment strip or band together which should now be holding the ring of seven rectangular magnets together, is to simply place the two quadropole ring/doughnut magnets on either end IE - Top and Bottom of the assembly and should also have the same like poles facing inwards so that all poles are alike and facing inward towards each other. Refer below to (reference #6)

I did not show the metal containment strip or band in this example so that you could see how the magnets poles should be oriented.

Remember that on the quadropole ring/doughnut magnets there are four poles to each magnet. Refer to (reference #7). On one side of the magnet the inside or center half is the north pole and on the outer half will be the south pole. The exact opposite will be the case on the flip side or reverse side of the magnet!

That's all there is to it! You should now be able to use this device for your experiments.

If you don't see evidence of ion projection you may have to flip or reverse both doughnut magnets you should then see evidence. You can test this by aiming the array directly towards a fluorescent light bulb. It is very obvious if you aim it towards an old junk TV and you can usually erase the evidence by the method I have described below. I will leave that for you to decide.

If for some other reason your device is not working, read through these instructions again and see if you mis-understood something because this is not something that is just a fluke of nature, it is proven science. If you have any questions, feel free to contact me and I will be more than willing to help in any way that I can. My email address is right there for you all to use and I am very passionate about the issues of FE/OU technologies. Together we will make these things known to the world to the point where these things can no longer be argued.

These are all of the supplies and information you should need to assemble this low energy "Ion Beam Projector" and at most, the total cost should not exceed the price of a dinner for two at the "Out Back" mate! So far, I have not seen this achieved anywhere else at a lower cost. I do know that, if you follow these directions that this device will project an ion beam to a considerable distance. Any upgrades are strictly up to you although I would suggest using these ferrite type magnets to start with and they should be plenty powerful for your initial experiments. There are of course other ways of making more powerful portable devices of this sort however, I will leave that up to your imagination. I am sure that many of you are getting the idea already and can imagine the possibilities and potential of this type of technology. I am sure that this will come up in later discussions within this forum and I am looking forward to hearing your thoughts on the matter. Also, to anyone who might be interested, I have done a lot of patent searching and have not been able to find such a simple and inexpensive design within the patent office so there is a good possibility that this design is open for patent if of course anyone is interested.

Personally I have found that every time I have applied or even gotten close to applying for a patent on an invention or design, that some multi-mega corporation always jumps in to push a patent through first anyway. I have had this happen to me many times and it seems to be more trouble then its worth to me. On top of that, this seems to have run in my family for several generations, in that someone else always takes credit for an invention and winds up raking in the dough and so, I have instead decided to share freely from now on. I am not suggesting that this is an unusual practice or that I alone have experienced this, on the contrary, it seems to be the norm in today's world. Also, I believe that the best way to stick it to those money hogs and power mongers is to upset their game entirely and give it directly to the masses where someone else might at least have a chance at it.

PLEASE REMEMBER: Much Caution should be taken during and after assembly of this device to NOT point the ion source or polar projections towards your TV or Computer Monitor or for that matter your Computer unless you have an old set or screen you want to use for your experiments. If you do this you will definitely see the evidence on any type Monitor or TV screen and may get a little upset. There is however a way to fix your Monitor or TV screen should you accidentally forget or get a little careless. On the other hand, the PC may not be so easy to fix unless you have a backup disk and are ready to re-format your hard drive etc... .

If you do screw up and wind up with a bright red or green dot on one of your screens you should be able to remedy this by placing a length of small ferrite magnets (like the ones you will have to buy in order to build this device), along a strip of permeable metal which the magnets will stick to (like the metal strip you will need to assemble this device) and then pass this arrangement in a rapid fashion over the face of your screen with the magnets side edges pointed towards the screen. In other words, metal strip side down, magnets face up with side edges of magnets directed towards the face of the screen. Do not rub or touch the screen directly but keep the strip of magnets within a couple inches of the screen. This will disrupt the charged field on your screen and will erase the dot. I had to do this myself and had to swipe this arrangement both horizontally and vertically many times before the otherwise permanent dot would disappear. It was a brand new big screen TV that I had just purchase the previous week and so I was really pissed and worried until I figured out how to fix the problem. Hopefully, this should work for you too, if it does not you might have to purchase a half dozen or so stronger magnets than the ones you tried the first time.

One more Note: Please be especially careful when experimenting with these devices outside and particularly in a thunderstorm okay? Duh

Stay in touch people there's much more to come. God bless you and keep you all. And please, ( BE CAREFUL ).

Comment from Jim

Sterling,

I do believe that the "Ion Source Beam Projector" that I have made available to the public does in fact have potential for "Radiant Energy" applications. "The Vasant Corporation" basically confirmed to me that this is most likely to be true in this case but was unsure how such a massive power surge could be controlled. Hey, I always say don't sweat the small stuff right? lol. I'm quite confident however that this would be a minor detail if only it would be allowed to be developed and used.

Jim

Ion Source Beam Project Open Sourcing Project

How to build an "Ion Source Beam Projector"

Comment from Jim

See also